It's mysterious but I don't know, what to do.
I let Hauptwerk migrate my 10-channel audio settings because I un-ticked the option "Discard migrated Hauptwerk v4 audio settings and reset audio device settings" when I first launched HW V5. It works fine and I named the 10 AsioChannels of my MOTU Ultralight Mk III in the appearing AudioDevice dialog with Main L, Main R, Stereo 2 L, Stereo 2 R, Stereo 3 L, Stereo 3 R, Stereo 4 L, Stereo 4 R und Stereo 5 L und Stereo 5 R.
These migrated audio outputs appear also in the Audio Mixer (for adding reverb, sorround/3D or multi-channel output) and in the audio mixer (Primary) Bus Groups (for multi channel output). I named them like in the audio device and in the audio mixer (for adding reverb, sorround/3D or multi-channel output) the migrated busses are correct connected with the audio output (device) channel(s). All migrated audio channels worked fine.
I route the divisions of an organ to only one Stereo-Pair, e.g. . = Main, Swell = Stereo 2, Positiv = Stereo 3, Pedal = Stereo 4 and if possible Rear = Stereo 5. It works fine.
Then I loaded St.Anne to exercise with adding a reverberation , went to the AudioMixer (for adding reverb....) choose "Mxr prst 1: *Mstr mix bus 1 *Stereo mix 1 (main/recording)" and selected a reverb with reverb audio output on Stereo 5 (Rear). After hearing and changing some reverbs I cleared all selected Inputs...and discarded any changes, if I was asked.
Now, surprise, the output level of "Mxr prst 1: Prmry bus 0013 'Migrated audio output'channel" = Stereo 4 (Asio 0007 L/0008 R) is about 7 db smaller than before and the other busses 0014 - 0017. But not only in Hauptwerk (normal) where I tried the additional reverb also in config 1 - 3. What has happened? I have controlled all busses, the audio device, the audio output connection... nothing. I restored to the fine migrated HW5 first launch day, nothing. But even when I make a backup or restore, after it Hauptwerk freezes (APPCHRASH in Hauptwerk.exe), so I'm not sure if the backup or restore was really successful... And if I restore, I have to load each organ in each config new, thats very time intensiv...e.g Rotterdam, Caen...
Where could be the problem or the reason that the Level of the bus decreased?
How can I solve this problem? I now have increased the audio output channel level +7 db in the "Audio mixer (for adding reverb....)" but its not the solving of the problem.
Thanks, Mike
I let Hauptwerk migrate my 10-channel audio settings because I un-ticked the option "Discard migrated Hauptwerk v4 audio settings and reset audio device settings" when I first launched HW V5. It works fine and I named the 10 AsioChannels of my MOTU Ultralight Mk III in the appearing AudioDevice dialog with Main L, Main R, Stereo 2 L, Stereo 2 R, Stereo 3 L, Stereo 3 R, Stereo 4 L, Stereo 4 R und Stereo 5 L und Stereo 5 R.
These migrated audio outputs appear also in the Audio Mixer (for adding reverb, sorround/3D or multi-channel output) and in the audio mixer (Primary) Bus Groups (for multi channel output). I named them like in the audio device and in the audio mixer (for adding reverb, sorround/3D or multi-channel output) the migrated busses are correct connected with the audio output (device) channel(s). All migrated audio channels worked fine.
I route the divisions of an organ to only one Stereo-Pair, e.g. . = Main, Swell = Stereo 2, Positiv = Stereo 3, Pedal = Stereo 4 and if possible Rear = Stereo 5. It works fine.
Then I loaded St.Anne to exercise with adding a reverberation , went to the AudioMixer (for adding reverb....) choose "Mxr prst 1: *Mstr mix bus 1 *Stereo mix 1 (main/recording)" and selected a reverb with reverb audio output on Stereo 5 (Rear). After hearing and changing some reverbs I cleared all selected Inputs...and discarded any changes, if I was asked.
Now, surprise, the output level of "Mxr prst 1: Prmry bus 0013 'Migrated audio output'channel" = Stereo 4 (Asio 0007 L/0008 R) is about 7 db smaller than before and the other busses 0014 - 0017. But not only in Hauptwerk (normal) where I tried the additional reverb also in config 1 - 3. What has happened? I have controlled all busses, the audio device, the audio output connection... nothing. I restored to the fine migrated HW5 first launch day, nothing. But even when I make a backup or restore, after it Hauptwerk freezes (APPCHRASH in Hauptwerk.exe), so I'm not sure if the backup or restore was really successful... And if I restore, I have to load each organ in each config new, thats very time intensiv...e.g Rotterdam, Caen...
Where could be the problem or the reason that the Level of the bus decreased?
How can I solve this problem? I now have increased the audio output channel level +7 db in the "Audio mixer (for adding reverb....)" but its not the solving of the problem.
Thanks, Mike